[Renzo Mischianti]

Hi George,
the log says that there is a wiring problem.

17:32:18.057 > ----------------------------------------
17:32:18.101 > The M0 and M1 pins is not set, this mean that you are connect directly the pins as you need!
17:32:18.199 > AUX HIGH!
17:32:18.209 > Complete!
17:32:18.221 > No response from device! (Check wiring)
17:32:18.265 > 12
17:32:18.268 > ----------------------------------------

Pay attention to M0 and M1 settings also.

Bye Renzo

[Renzo Mischianti]

Hi George,
this week I can’t explore these problems.
But I check all when return.

For the RSSI remember to activate It in the device configuration.

Try to use a structure to check if the problem persists.

Bye Renzo

[Renzo Mischianti]

Hi Gulpman,
It’s true, and I’m going to adjust something. I reused some schema from the previous article, and I don’t give attention to the single label, only to the connection schema.

But AUX isn’t connected (to the microcontroller) but It’s pulled up.

Thanks for the alert about that issues, if you find something else alert me.

Bye Renzo

[Renzo Mischianti]

Hi LeoLage,
I check in the protocol manual, and I can’t find that option

Download!

I think isn’t possible to retrieve via rs485.
Try to check in the document.

Bye Renzo

[Renzo Mischianti]

Hi Tengku,
what configuration do you use on the server and receiver?
Bye Renzo

[Renzo Mischianti]

Hi Klaas,
sorry but I add a cycling link and I freeze de forum.

Other people have tried to use that device with different results.

E22 Wiring and Constructor Validation

E90-DTU (400SL22P)

But if you configure correctly the device you can use this library.

Bye Renzo

[Renzo Mischianti]

Good! If you need more help, write without problems.
And if you want, share your projects.
Bye Renzo

[Renzo Mischianti]

Hi leolage,
In the inverter, like my model, there are the data like the total productions since the installation, or the production of the current day, but not the production of a specified day, i don’t know if exists some model with the history data.

But all the command available from the inverter inverter are explained in the article

ABB Aurora PV inverter library for Arduino, esp8266 and esp32

You can retrieve a lot of data.

Bye Renzo

[Renzo Mischianti]

Hi LeoLage,
no sorry, I create that device for alerts and also to store the old data.
I the SD is corrupted try to put it on the PC and restore the data.
Can you put a photo of your installation?
Bye Renzo

[Renzo Mischianti]

Ahhh! Ok
It isn’t an icon set is the custom firmware of the Flying bear Ghost that had a custom graphics
Bye Renzo

[Renzo Mischianti]

Hi Mike,
Use the dynamic ip than use the my wifi firmware to set the static ip.
Bye Renzo

[Renzo Mischianti]

Hi Mike,
No no other people have this issue. Probably is the firmware of the printer.
Bye Renzo

[Renzo Mischianti]

Hi Kev,
you must uncomment the
#define EMAIL_SENDER_DEBUG
on EMailSenderKey.h.

[Renzo Mischianti]

Hi Flaminio,
the configuration of the devices is independent of the SimpleFTPServer library, you must only select the correct config in FtpServerKey.h as you can read in the articles.

FTP server on esp8266 and esp32

Bye Renzo

[Renzo Mischianti]

Hi,
Do the other commands works correctly?
Bye Renzo

[Author]

Posts