Configurazione del Modulo RF EByte E70 (esp32, STM32, Arduino, Raspberry Pi Pico)

ResponseStructContainer getConfiguration();

struct Speed {
	uint8_t airDataRate :3; //bit 0-2
	String getAirDataRateDescription() {
		return getAirDataRateDescriptionByParams(this->airDataRate);
	}

	uint8_t uartBaudRate :3; //bit 3-5
	String getUARTBaudRateDescription() {
		return getUARTBaudRateDescriptionByParams(this->uartBaudRate);
	}

    uint8_t uartParity :2; //bit 6-7
    String getUARTParityDescription() {
        return getUARTParityDescriptionByParams(this->uartParity);
    }

};

struct Option {
	uint8_t transmissionPower :2; //bit 0-1
	String getTransmissionPowerDescription() {
		return getTransmissionPowerDescriptionByParams(this->transmissionPower);
	}

    byte ioDriveMode  		: 1; //bit 2
    String getIODroveModeDescription() {
        return getIODriveModeDescriptionDescriptionByParams(this->ioDriveMode);
    }

    byte fec       		: 1; //bit 3
    String getFECDescription() {
        return getFECDescriptionByParams(this->fec);
    }


    byte wirelessWakeupTime : 3; //bit 4-6
    String getWirelessWakeUPTimeDescription() {
        return getWirelessWakeUPTimeDescriptionByParams(this->wirelessWakeupTime);
    }

    byte fixedTransmission :1; //bit 7
    String getFixedTransmissionDescription() {
        return getFixedTransmissionDescriptionByParams(this->fixedTransmission);
    }

};

struct Channel {
    uint8_t CHAN :5; // bit 0-4
    String getChannelDescription( ) {
        return String(this->CHAN + OPERATING_FREQUENCY) + F("MHz");
    }

    uint8_t subPacketSetting :3; //bit 5-7
    String getSubPacketSetting() {
        return getSubPacketSettingByParams(this->subPacketSetting);
    }

};

struct Configuration {
	byte COMMAND = 0;

	byte ADDH = 0;
	byte ADDL = 0;

	struct Speed SPED;
    struct Channel CHAN;

	struct Option OPTION;
};

/*
 * RF E70
 * Get configuration.
 * You must uncommend the correct constructor.
 *
 * by Renzo Mischianti <https://www.mischianti.org>
 *
 * https://www.mischianti.org
 *
 * E70		  ----- WeMos D1 mini	----- esp32			----- Arduino Nano 33 IoT	----- Arduino MKR	----- Raspberry Pi Pico   ----- stm32               ----- ArduinoUNO
 * M0         ----- D6 				----- 23 			----- 4 					----- 2 			----- 9 			      ----- PB0 		       	----- 8 Volt div
 * M1         ----- D7 				----- 19 			----- 5 					----- 3 			----- 10 			      ----- PB1 		       	----- 7 Volt div
 * M1         ----- D8 				----- 22 			----- 6 					----- 4 			----- 11 			      ----- PB10 		      	----- 6 Volt div
 * TX         ----- D3 (PullUP)		----- TX2 (PullUP)	----- TX1 (PullUP)			----- 14 (PullUP)	----- 8 (PullUP)	      ----- PA2 TX2 (PullUP)    ----- 4 (PullUP)
 * RX         ----- D4 (PullUP)		----- RX2 (PullUP)	----- RX1 (PullUP)			----- 13 (PullUP)	----- 9 (PullUP)	      ----- PA3 RX2 (PullUP)    ----- 5 Volt div (PullUP)
 * AUX        ----- D5 (PullUP)		----- 18  (PullUP)	----- 2  (PullUP)			----- 0  (PullUP)	----- 2  (PullUP)	      ----- PA0  (PullUP)       ----- 3 (PullUP)
 * VCC        ----- 3.3v/5v			----- 3.3v/5v		----- 3.3v/5v				----- 3.3v/5v		----- 3.3v/5v		      ----- 3.3v/5v             ----- 3.3v/5v
 * GND        ----- GND				----- GND			----- GND					----- GND			----- GND			      ----- GND                 ----- GND
 *
 *	Configuration can be emulated by set
 *	M0 = HIGH
 *	M1 = HIGH
 *	M2 = LOW
 *
 */

#include "Arduino.h"
#include "RF_E70.h"


// ---------- esp8266 pins --------------
//RF_E70 e70ttl(RX, TX, AUX, M0, M1, M2);  // Arduino RX <-- e70 TX, Arduino TX --> e70 RX
//RF_E70 e70ttl(D3, D4, D5, D7, D6, D7); // Arduino RX <-- e70 TX, Arduino TX --> e70 RX AUX M0 M1
//RF_E70 e70ttl(D2, D3); // Config without connect AUX and M0 M1

//#include <SoftwareSerial.h>
//SoftwareSerial mySerial(D2, D3); // Arduino RX <-- e70 TX, Arduino TX --> e70 RX
//RF_E70 e70ttl(&mySerial, D5, D6, D7, D8); // AUX M0 M1
// -------------------------------------

// ---------- Arduino pins --------------
//RF_E70 e70ttl(4, 5, 3, 8, 7, 6); // Arduino RX <-- e70 TX, Arduino TX --> e70 RX AUX M0 M1
//RF_E70 e70ttl(4, 5); // Config without connect AUX and M0 M1

//#include <SoftwareSerial.h>
//SoftwareSerial mySerial(4, 5); // Arduino RX <-- e70 TX, Arduino TX --> e70 RX
//RF_E70 e70ttl(&mySerial, 3, 8, 7, 6); // AUX M0 M1
// -------------------------------------

// ------------- Arduino Nano 33 IoT -------------
// RF_E70 e70ttl(&Serial1, 2, 4, 5, 6); //  RX AUX M0 M1
// -------------------------------------------------

// ------------- Arduino MKR WiFi 1010 -------------
// RF_E70 e70ttl(&Serial1, 0, 2, 3, 4); //  RX AUX M0 M1
// -------------------------------------------------

// ---------- esp32c3 pins --------------
// RF_E70 e70ttl(&Serial1,  1, 2, 3, 4,); //  RX AUX M0 M1

RF_E70 e70ttl(4, 5, &Serial1, 6, 1, 2, 3, UART_BPS_RATE_9600); //  esp32 RX <-- e70 TX, esp32 TX --> e70 RX AUX M0 M1
// -------------------------------------

// ---------- esp32 pins --------------
// RF_E70 e70ttl(&Serial2, 15, 23, 19, 22); //  RX AUX M0 M1

//RF_E70 e70ttl(&Serial2, 22, 4, 18, 21, 19, UART_BPS_RATE_9600); //  esp32 RX <-- e70 TX, esp32 TX --> e70 RX AUX M0 M1
// -------------------------------------

// ---------- Raspberry PI Pico pins --------------
// RF_E70 e70ttl(&Serial2, 2, 10, 11, 12); //  RX AUX M0 M1
// -------------------------------------

// ---------------- STM32 --------------------
// HardwareSerial Serial2(USART2);   // PA3  (RX)  PA2  (TX)
// RF_E70 e70ttl(&Serial2, PA0, PB0, PB1, PB10); //  RX AUX M0 M1
// -------------------------------------------------

void printParameters(struct Configuration configuration);
void printModuleInformation(struct ModuleInformation moduleInformation);

void setup() {
	Serial.begin(9600);
#if defined(ARDUINO_ARCH_STM32) || defined(__STM32F1__) || defined(__STM32F4__)
	Serial.dtr(false);
#endif

	while(!Serial){};
	delay(500);

	Serial.println("INIT!!");

	// Startup all pins and UART
	e70ttl.begin();

	ResponseStructContainer c;
	c = e70ttl.getConfiguration();
	// It's important get configuration pointer before all other operation
	Configuration configuration = *(Configuration*) c.data;
	Serial.println(c.status.getResponseDescription());
	Serial.println(c.status.code);

	printParameters(configuration);

	ResponseStructContainer cMi;
	cMi = e70ttl.getModuleInformation();
	// It's important get information pointer before all other operation
	ModuleInformation mi = *(ModuleInformation*)cMi.data;

	Serial.println(cMi.status.getResponseDescription());
	Serial.println(cMi.status.code);

	printModuleInformation(mi);

	c.close();
	cMi.close();
}

void loop() {

}
void printParameters(struct Configuration configuration) {
	Serial.println("----------------------------------------");

	Serial.print(F("Configuration packet: "));
    byte* byteArray = (byte*)&configuration;  // Cast the address of config to a byte pointer
    for (int i = 0; i < sizeof(Configuration); i++) {
        if (byteArray[i] < 16) {
            Serial.print('0');  // Print a leading zero for single-digit hex values
        }
        Serial.print(byteArray[i], HEX);  // Print each byte of the struct in hexadecimal
        Serial.print(" ");
    }
    Serial.println(F(" "));

	Serial.print(F("HEAD : "));  Serial.print(configuration.COMMAND, HEX);Serial.print(" ");
	Serial.println(F(" "));
	Serial.print(F("AddH : "));  Serial.println(configuration.ADDH, HEX);
	Serial.print(F("AddL : "));  Serial.println(configuration.ADDL, HEX);
	Serial.println(F(" "));
	Serial.print(F("Chan : "));  Serial.print(configuration.CHAN.CHAN, DEC); Serial.print(" -> "); Serial.println(configuration.CHAN.getChannelDescription());
	Serial.println(F(" "));
	Serial.print(F("SpeedParityBit     : "));  Serial.print(configuration.SPED.uartParity, BIN);Serial.print(" -> "); Serial.println(configuration.SPED.getUARTParityDescription());
	Serial.print(F("SpeedUARTDatte     : "));  Serial.print(configuration.SPED.uartBaudRate, BIN);Serial.print(" -> "); Serial.println(configuration.SPED.getUARTBaudRateDescription());
	Serial.print(F("SpeedAirDataRate   : "));  Serial.print(configuration.SPED.airDataRate, BIN);Serial.print(" -> "); Serial.println(configuration.SPED.getAirDataRateDescription());
	Serial.println(F(" "));
	Serial.print(F("OptionFECPacketSett: "));  Serial.print(configuration.OPTION.fec, BIN);Serial.print(" -> "); Serial.println(configuration.OPTION.getFECDescription());
	Serial.print(F("OptionTranPower    : "));  Serial.print(configuration.OPTION.transmissionPower, BIN);Serial.print(" -> "); Serial.println(configuration.OPTION.getTransmissionPowerDescription());
	Serial.print(F("OptionIODrive: "));  Serial.print(configuration.OPTION.ioDriveMode, BIN);Serial.print(" -> "); Serial.println(configuration.OPTION.getIODroveModeDescription());
	Serial.print(F("OptionFixedTransmission: "));  Serial.print(configuration.OPTION.fixedTransmission, BIN);Serial.print(" -> "); Serial.println(configuration.OPTION.getFixedTransmissionDescription());
	Serial.print(F("OptionWirelessWakeUPTime: "));  Serial.print(configuration.OPTION.wirelessWakeupTime, BIN);Serial.print(" -> "); Serial.println(configuration.OPTION.getWirelessWakeUPTimeDescription());


	Serial.println("----------------------------------------");
}
void printModuleInformation(struct ModuleInformation moduleInformation) {
	Serial.println("----------------------------------------");
	Serial.print(F("HEAD: "));  Serial.print(moduleInformation.COMMAND, HEX);Serial.print(" ");

	Serial.print(F("Model no.: "));  Serial.println(moduleInformation.model, HEX);
	Serial.print(F("Version  : "));  Serial.println(moduleInformation.version, HEX);
	Serial.print(F("Features : "));  Serial.println(moduleInformation.features1, HEX);
	Serial.print(F("Features : "));  Serial.println(moduleInformation.features2, HEX);
	Serial.print(F("Features : "));  Serial.println(moduleInformation.features3, HEX);
	Serial.print(F("Features : "));  Serial.println(moduleInformation.features4, HEX);
	Serial.println("----------------------------------------");
}

INIT!!
Success
1
----------------------------------------
Configuration packet: C0 00 02 18 44 9C   
HEAD : C0  
AddH : 0
AddL : 2
 
Chan : 4 -> 414MHz
 
SpeedParityBit     : 0 -> 8N1 (Default)
SpeedUARTDatte     : 11 -> 9600bps (default)
SpeedAirDataRate   : 0 -> 2.5kbps (default)
 
OptionFECPacketSett: 1 -> Turn on Forward Error Correction Switch (Default)
OptionTranPower    : 0 -> 22dBm (Default)
OptionIODrive: 1 -> TXD, RXD, AUX are push-pulls/pull-ups (default)
OptionFixedTransmission: 1 -> Fixed transmission (first three bytes can be used as high/low address and channel)
OptionWirelessWakeUPTime: 1 -> 1000ms (default)
----------------------------------------
No response from device! (Check wiring)
12
----------------------------------------
HEAD: 31 Model no.: 30
Version  : 30
Features : 30
Features : 6D
Features : 73
Features : 20
----------------------------------------

#define E70_22 // valore predefinito senza impostazione 

#define E70_30

// One of 
#define FREQUENCY_433 
#define FREQUENCY_868
#define FREQUENCY_900
#define FREQUENCY_915

		ResponseStatus setConfiguration(Configuration configuration, PROGRAM_COMMAND saveType = WRITE_CFG_PWR_DWN_LOSE);

	ResponseStructContainer c;
	c = e70ttl.getConfiguration();
	// It's important get configuration pointer before all other operation
	Configuration configuration = *(Configuration*) c.data;
	Serial.println(c.status.getResponseDescription());
	Serial.println(c.status.code);

	printParameters(configuration);
	configuration.ADDL = 0x00;  // First part of address
	configuration.ADDH = 0x00; // Second part


	configuration.SPED.uartBaudRate = UART_BPS_9600; // Serial baud rate
	configuration.SPED.airDataRate = AIR_DATA_RATE_000_025; // Air baud rate
	configuration.SPED.uartParity = MODE_00_8N1; // Parity bit

	configuration.CHAN.CHAN = 4;
	configuration.CHAN.subPacketSetting = SPS_0064_010;

	configuration.OPTION.fec = FEC_1_ON; // Packet size
	configuration.OPTION.fixedTransmission = FT_TRANSPARENT_TRANSMISSION; // Need to send special command
	configuration.OPTION.transmissionPower = POWER_30; // Device power
	configuration.OPTION.ioDriveMode = IO_D_MODE_PUSH_PULLS_PULL_UPS; // IO Drive
	configuration.OPTION.wirelessWakeupTime = WAKE_UP_1000; // Wake up time

	// Set configuration changed and set to not hold the configuration
	ResponseStatus rs = e70ttl.setConfiguration(configuration, WRITE_CFG_PWR_DWN_LOSE);
	Serial.println(rs.getResponseDescription());
	Serial.println(rs.code);
	printParameters(configuration);
    c.close()

/*
 * RF E70
 * Set configuration.
 *
 * You must uncommend the correct constructor.
 *
 * by Renzo Mischianti <https://www.mischianti.org>
 *
 * https://www.mischianti.org
 *
 * E70		  ----- WeMos D1 mini	----- esp32			----- Arduino Nano 33 IoT	----- Arduino MKR	----- Raspberry Pi Pico   ----- stm32               ----- ArduinoUNO
 * M0         ----- D6 				----- 23 			----- 4 					----- 2 			----- 9 			      ----- PB0 		       	----- 8 Volt div
 * M1         ----- D7 				----- 19 			----- 5 					----- 3 			----- 10 			      ----- PB1 		       	----- 7 Volt div
 * M1         ----- D8 				----- 22 			----- 6 					----- 4 			----- 11 			      ----- PB10 		      	----- 6 Volt div
 * TX         ----- D3 (PullUP)		----- TX2 (PullUP)	----- TX1 (PullUP)			----- 14 (PullUP)	----- 8 (PullUP)	      ----- PA2 TX2 (PullUP)    ----- 4 (PullUP)
 * RX         ----- D4 (PullUP)		----- RX2 (PullUP)	----- RX1 (PullUP)			----- 13 (PullUP)	----- 9 (PullUP)	      ----- PA3 RX2 (PullUP)    ----- 5 Volt div (PullUP)
 * AUX        ----- D5 (PullUP)		----- 18  (PullUP)	----- 2  (PullUP)			----- 0  (PullUP)	----- 2  (PullUP)	      ----- PA0  (PullUP)       ----- 3 (PullUP)
 * VCC        ----- 3.3v/5v			----- 3.3v/5v		----- 3.3v/5v				----- 3.3v/5v		----- 3.3v/5v		      ----- 3.3v/5v             ----- 3.3v/5v
 * GND        ----- GND				----- GND			----- GND					----- GND			----- GND			      ----- GND                 ----- GND
 *
 *	Configuration can be emulated by set
 *	M0 = HIGH
 *	M1 = HIGH
 *	M2 = LOW
 *
 */
#include "Arduino.h"
#include "RF_E70.h"

// ---------- esp8266 pins --------------
//RF_E70 e70ttl(RX, TX, AUX, M0, M1, M2);  // Arduino RX <-- e70 TX, Arduino TX --> e70 RX
//RF_E70 e70ttl(D3, D4, D5, D7, D6, D7); // Arduino RX <-- e70 TX, Arduino TX --> e70 RX AUX M0 M1
//RF_E70 e70ttl(D2, D3); // Config without connect AUX and M0 M1

//#include <SoftwareSerial.h>
//SoftwareSerial mySerial(D2, D3); // Arduino RX <-- e70 TX, Arduino TX --> e70 RX
//RF_E70 e70ttl(&mySerial, D5, D6, D7, D8); // AUX M0 M1
// -------------------------------------

// ---------- Arduino pins --------------
//RF_E70 e70ttl(4, 5, 3, 8, 7, 6); // Arduino RX <-- e70 TX, Arduino TX --> e70 RX AUX M0 M1
//RF_E70 e70ttl(4, 5); // Config without connect AUX and M0 M1

//#include <SoftwareSerial.h>
//SoftwareSerial mySerial(4, 5); // Arduino RX <-- e70 TX, Arduino TX --> e70 RX
//RF_E70 e70ttl(&mySerial, 3, 8, 7, 6); // AUX M0 M1
// -------------------------------------

// ------------- Arduino Nano 33 IoT -------------
// RF_E70 e70ttl(&Serial1, 2, 4, 5, 6); //  RX AUX M0 M1
// -------------------------------------------------

// ------------- Arduino MKR WiFi 1010 -------------
// RF_E70 e70ttl(&Serial1, 0, 2, 3, 4); //  RX AUX M0 M1
// -------------------------------------------------

// ---------- esp32c3 pins --------------
// RF_E70 e70ttl(&Serial1,  1, 2, 3, 4,); //  RX AUX M0 M1

//RF_E70 e70ttl(4, 5, &Serial1, 6, 1, 2, 3, UART_BPS_RATE_9600); //  esp32 RX <-- e70 TX, esp32 TX --> e70 RX AUX M0 M1
// -------------------------------------

// ---------- esp32 pins --------------
 RF_E70 e70ttl(&Serial2, 15, 23, 19, 22); //  RX AUX M0 M1

//RF_E70 e70ttl(&Serial2, 22, 4, 18, 21, 19, UART_BPS_RATE_9600); //  esp32 RX <-- e70 TX, esp32 TX --> e70 RX AUX M0 M1
// -------------------------------------

// ---------- Raspberry PI Pico pins --------------
// RF_E70 e70ttl(&Serial2, 2, 10, 11, 12); //  RX AUX M0 M1
// -------------------------------------

// ---------------- STM32 --------------------
// HardwareSerial Serial2(USART2);   // PA3  (RX)  PA2  (TX)
// RF_E70 e70ttl(&Serial2, PA0, PB0, PB1, PB10); //  RX AUX M0 M1
// -------------------------------------------------

void printParameters(struct Configuration configuration);
void printModuleInformation(struct ModuleInformation moduleInformation);

void setup() {
	Serial.begin(9600);
#if defined(ARDUINO_ARCH_STM32) || defined(__STM32F1__) || defined(__STM32F4__)
	Serial.dtr(false);
#endif

	while(!Serial){};
	delay(500);

	Serial.println();


	// Startup all pins and UART
	e70ttl.begin();

	Serial.println("Retrieve configuration!");
	ResponseStructContainer c;
	c = e70ttl.getConfiguration();
	// It's important get configuration pointer before all other operation
	Configuration configuration = *(Configuration*) c.data;
	Serial.println(c.status.getResponseDescription());
	Serial.println(c.status.code);

	printParameters(configuration);

//	----------------------- DEFAULT TRANSPARENT -----------------------
	configuration.ADDL = 0x00;  // First part of address
	configuration.ADDH = 0x00; // Second part


	configuration.SPED.uartBaudRate = UART_BPS_9600; // Serial baud rate
	configuration.SPED.airDataRate = AIR_DATA_RATE_000_025; // Air baud rate
	configuration.SPED.uartParity = MODE_00_8N1; // Parity bit

	configuration.CHAN.CHAN = 4;
	configuration.CHAN.subPacketSetting = SPS_0064_010;

	configuration.OPTION.fec = FEC_1_ON; // Packet size
	configuration.OPTION.fixedTransmission = FT_TRANSPARENT_TRANSMISSION; // Need to send special command
	configuration.OPTION.transmissionPower = POWER_22; // Device power
	configuration.OPTION.ioDriveMode = IO_D_MODE_PUSH_PULLS_PULL_UPS; // IO Drive
	configuration.OPTION.wirelessWakeupTime = WAKE_UP_1000; // Wake up time
//	----------------------- FIXED SENDER -----------------------
//	configuration.ADDL = 0x02;  // First part of address
//	configuration.ADDH = 0x00; // Second part
//
//
//	configuration.SPED.uartBaudRate = UART_BPS_9600; // Serial baud rate
//	configuration.SPED.airDataRate = AIR_DATA_RATE_000_025; // Air baud rate
//	configuration.SPED.uartParity = MODE_00_8N1; // Parity bit
//
//	configuration.CHAN.CHAN = 4;
//	configuration.CHAN.subPacketSetting = SPS_0064_010;
//
//	configuration.OPTION.fec = FEC_1_ON; // Packet size
//	configuration.OPTION.fixedTransmission = FT_FIXED_TRANSMISSION; // Need to send special command
//	configuration.OPTION.transmissionPower = POWER_22; // Device power
//	configuration.OPTION.ioDriveMode = IO_D_MODE_PUSH_PULLS_PULL_UPS; // IO Drive
//	configuration.OPTION.wirelessWakeupTime = WAKE_UP_1000; // Wake up time
//
//	----------------------- FIXED RECEIVER -----------------------
//	configuration.ADDL = 0x03;  // First part of address
//	configuration.ADDH = 0x00; // Second part
//
//
//	configuration.SPED.uartBaudRate = UART_BPS_9600; // Serial baud rate
//	configuration.SPED.airDataRate = AIR_DATA_RATE_000_025; // Air baud rate
//	configuration.SPED.uartParity = MODE_00_8N1; // Parity bit
//
//	configuration.CHAN.CHAN = 4;
//	configuration.CHAN.subPacketSetting = SPS_0064_010;
//
//	configuration.OPTION.fec = FEC_1_ON; // Packet size
//	configuration.OPTION.fixedTransmission = FT_FIXED_TRANSMISSION; // Need to send special command
//	configuration.OPTION.transmissionPower = POWER_22; // Device power
//	configuration.OPTION.ioDriveMode = IO_D_MODE_PUSH_PULLS_PULL_UPS; // IO Drive
//	configuration.OPTION.wirelessWakeupTime = WAKE_UP_1000; // Wake up time
//
//	----------------------- CONTINOUS RECEIVER & SENDER -----------------------
//	configuration.ADDL = 0x01;  // First part of address
//	configuration.ADDH = 0x00; // Second part
//
//
//	configuration.SPED.uartBaudRate = UART_BPS_9600; // Serial baud rate
//	configuration.SPED.airDataRate = AIR_DATA_RATE_000_025; // Air baud rate
//	configuration.SPED.uartParity = MODE_00_8N1; // Parity bit
//
//	configuration.CHAN.CHAN = 4;
//	configuration.CHAN.subPacketSetting = SPS_0064_010;
//
//	configuration.OPTION.fec = FEC_1_ON; // Packet size
//	configuration.OPTION.fixedTransmission = FT_FIXED_TRANSMISSION; // Need to send special command
//	configuration.OPTION.transmissionPower = POWER_22; // Device power
//	configuration.OPTION.ioDriveMode = IO_D_MODE_PUSH_PULLS_PULL_UPS; // IO Drive
//	configuration.OPTION.wirelessWakeupTime = WAKE_UP_1000; // Wake up time
//
//	----------------------- BROADCAST MESSAGE 1 -----------------------
//	configuration.ADDL = 0x04;  // First part of address
//	configuration.ADDH = 0x00; // Second part
//
//
//	configuration.SPED.uartBaudRate = UART_BPS_9600; // Serial baud rate
//	configuration.SPED.airDataRate = AIR_DATA_RATE_000_025; // Air baud rate
//	configuration.SPED.uartParity = MODE_00_8N1; // Parity bit
//
//	configuration.CHAN.CHAN = 4;
//	configuration.CHAN.subPacketSetting = SPS_0064_010;
//
//	configuration.OPTION.fec = FEC_1_ON; // Packet size
//	configuration.OPTION.fixedTransmission = FT_FIXED_TRANSMISSION; // Need to send special command
//	configuration.OPTION.transmissionPower = POWER_22; // Device power
//	configuration.OPTION.ioDriveMode = IO_D_MODE_PUSH_PULLS_PULL_UPS; // IO Drive
//	configuration.OPTION.wirelessWakeupTime = WAKE_UP_1000; // Wake up time
//	----------------------- BROADCAST MESSAGE 2 -----------------------
//	configuration.ADDL = 0x05;  // First part of address
//	configuration.ADDH = 0x00; // Second part
//
//
//	configuration.SPED.uartBaudRate = UART_BPS_9600; // Serial baud rate
//	configuration.SPED.airDataRate = AIR_DATA_RATE_000_025; // Air baud rate
//	configuration.SPED.uartParity = MODE_00_8N1; // Parity bit
//
//	configuration.CHAN.CHAN = 4;
//	configuration.CHAN.subPacketSetting = SPS_0064_010;
//
//	configuration.OPTION.fec = FEC_1_ON; // Packet size
//	configuration.OPTION.fixedTransmission = FT_FIXED_TRANSMISSION; // Need to send special command
//	configuration.OPTION.transmissionPower = POWER_22; // Device power
//	configuration.OPTION.ioDriveMode = IO_D_MODE_PUSH_PULLS_PULL_UPS; // IO Drive
//	configuration.OPTION.wirelessWakeupTime = WAKE_UP_1000; // Wake up time
//	----------------------- BROADCAST MESSAGE 3 -----------------------
//	configuration.ADDL = 0x05;  // First part of address
//	configuration.ADDH = 0x00; // Second part
//
//
//	configuration.SPED.uartBaudRate = UART_BPS_9600; // Serial baud rate
//	configuration.SPED.airDataRate = AIR_DATA_RATE_000_025; // Air baud rate
//	configuration.SPED.uartParity = MODE_00_8N1; // Parity bit
//
//	configuration.CHAN.CHAN = 4;
//	configuration.CHAN.subPacketSetting = SPS_0064_010;
//
//	configuration.OPTION.fec = FEC_1_ON; // Packet size
//	configuration.OPTION.fixedTransmission = FT_FIXED_TRANSMISSION; // Need to send special command
//	configuration.OPTION.transmissionPower = POWER_22; // Device power
//	configuration.OPTION.ioDriveMode = IO_D_MODE_PUSH_PULLS_PULL_UPS; // IO Drive
//	configuration.OPTION.wirelessWakeupTime = WAKE_UP_1000; // Wake up time
//	----------------------- MONITORING -----------------------
//	configuration.ADDL = BROADCAST_ADDRESS;  // First part of address
//	configuration.ADDH = BROADCAST_ADDRESS; // Second part
//
//
//	configuration.SPED.uartBaudRate = UART_BPS_9600; // Serial baud rate
//	configuration.SPED.airDataRate = AIR_DATA_RATE_000_025; // Air baud rate
//	configuration.SPED.uartParity = MODE_00_8N1; // Parity bit
//
//	configuration.CHAN.CHAN = 4;
//	configuration.CHAN.subPacketSetting = SPS_0064_010;
//
//	configuration.OPTION.fec = FEC_1_ON; // Packet size
//	configuration.OPTION.fixedTransmission = FT_FIXED_TRANSMISSION; // Need to send special command
//	configuration.OPTION.transmissionPower = POWER_22; // Device power
//	configuration.OPTION.ioDriveMode = IO_D_MODE_PUSH_PULLS_PULL_UPS; // IO Drive
//	configuration.OPTION.wirelessWakeupTime = WAKE_UP_1000; // Wake up time

	Serial.println("Set configuration!");
	// Set configuration changed and set to not hold the configuration
	ResponseStatus rs = e70ttl.setConfiguration(configuration, WRITE_CFG_PWR_DWN_SAVE);
	Serial.println(rs.getResponseDescription());
	Serial.println(rs.code);

	Serial.println("Retrieve configuration!");
	c = e70ttl.getConfiguration();
	// It's important get configuration pointer before all other operation
	configuration = *(Configuration*) c.data;
	Serial.println(c.status.getResponseDescription());
	Serial.println(c.status.code);

	printParameters(configuration);
	c.close();
}

void loop() {

}
void printParameters(struct Configuration configuration) {
	Serial.println("----------------------------------------");

	Serial.print(F("Configuration packet: "));
    byte* byteArray = (byte*)&configuration;  // Cast the address of config to a byte pointer
    for (int i = 0; i < sizeof(Configuration); i++) {
        if (byteArray[i] < 16) {
            Serial.print('0');  // Print a leading zero for single-digit hex values
        }
        Serial.print(byteArray[i], HEX);  // Print each byte of the struct in hexadecimal
        Serial.print(" ");
    }
    Serial.println(F(" "));

	Serial.print(F("HEAD : "));  Serial.print(configuration.COMMAND, HEX);Serial.print(" ");
	Serial.println(F(" "));
	Serial.print(F("AddH : "));  Serial.println(configuration.ADDH, HEX);
	Serial.print(F("AddL : "));  Serial.println(configuration.ADDL, HEX);
	Serial.println(F(" "));
	Serial.print(F("Chan : "));  Serial.print(configuration.CHAN.CHAN, DEC); Serial.print(" -> "); Serial.println(configuration.CHAN.getChannelDescription());
	Serial.print(F("Packet size : "));  Serial.print(configuration.CHAN.subPacketSetting, BIN); Serial.print(" -> "); Serial.println(configuration.CHAN.getSubPacketSetting());
	Serial.println(F(" "));
	Serial.print(F("SpeedParityBit     : "));  Serial.print(configuration.SPED.uartParity, BIN);Serial.print(" -> "); Serial.println(configuration.SPED.getUARTParityDescription());
	Serial.print(F("SpeedUARTDatte     : "));  Serial.print(configuration.SPED.uartBaudRate, BIN);Serial.print(" -> "); Serial.println(configuration.SPED.getUARTBaudRateDescription());
	Serial.print(F("SpeedAirDataRate   : "));  Serial.print(configuration.SPED.airDataRate, BIN);Serial.print(" -> "); Serial.println(configuration.SPED.getAirDataRateDescription());
	Serial.println(F(" "));
	Serial.print(F("OptionFECPacketSett: "));  Serial.print(configuration.OPTION.fec, BIN);Serial.print(" -> "); Serial.println(configuration.OPTION.getFECDescription());
	Serial.print(F("OptionTranPower    : "));  Serial.print(configuration.OPTION.transmissionPower, BIN);Serial.print(" -> "); Serial.println(configuration.OPTION.getTransmissionPowerDescription());
	Serial.print(F("OptionIODrive: "));  Serial.print(configuration.OPTION.ioDriveMode, BIN);Serial.print(" -> "); Serial.println(configuration.OPTION.getIODroveModeDescription());
	Serial.print(F("OptionFixedTransmission: "));  Serial.print(configuration.OPTION.fixedTransmission, BIN);Serial.print(" -> "); Serial.println(configuration.OPTION.getFixedTransmissionDescription());
	Serial.print(F("OptionWirelessWakeUPTime: "));  Serial.print(configuration.OPTION.wirelessWakeupTime, BIN);Serial.print(" -> "); Serial.println(configuration.OPTION.getWirelessWakeUPTimeDescription());


	Serial.println("----------------------------------------");
}
void printModuleInformation(struct ModuleInformation moduleInformation) {
	Serial.println("----------------------------------------");
	Serial.print(F("HEAD: "));  Serial.print(moduleInformation.COMMAND, HEX);Serial.print(" ");

	Serial.print(F("Model no.: "));  Serial.println(moduleInformation.model, HEX);
	Serial.print(F("Version  : "));  Serial.println(moduleInformation.version, HEX);
	Serial.print(F("Features : "));  Serial.println(moduleInformation.features1, HEX);
	Serial.print(F("Features : "));  Serial.println(moduleInformation.features2, HEX);
	Serial.print(F("Features : "));  Serial.println(moduleInformation.features3, HEX);
	Serial.print(F("Features : "));  Serial.println(moduleInformation.features4, HEX);
	Serial.println("----------------------------------------");
}

Retrieve configuration!
Success
1
----------------------------------------
Configuration packet: C0 00 00 18 44 1C   
HEAD : C0  
AddH : 0
AddL : 0
 
Chan : 4 -> 414MHz
Packet size : 10 -> 64bytes (default)
 
SpeedParityBit     : 0 -> 8N1 (Default)
SpeedUARTDatte     : 11 -> 9600bps (default)
SpeedAirDataRate   : 0 -> 2.5kbps (default)
 
OptionFECPacketSett: 1 -> Turn on Forward Error Correction Switch (Default)
OptionTranPower    : 0 -> 22dBm (Default)
OptionIODrive: 1 -> TXD, RXD, AUX are push-pulls/pull-ups (default)
OptionFixedTransmission: 0 -> Transparent transmission (default)
OptionWirelessWakeUPTime: 1 -> 1000ms (default)
----------------------------------------
Set configuration!
Success
1
Retrieve configuration!
Success
1
----------------------------------------
Configuration packet: C0 00 00 18 44 1C   
HEAD : C0  
AddH : 0
AddL : 0
 
Chan : 4 -> 414MHz
Packet size : 10 -> 64bytes (default)
 
SpeedParityBit     : 0 -> 8N1 (Default)
SpeedUARTDatte     : 11 -> 9600bps (default)
SpeedAirDataRate   : 0 -> 2.5kbps (default)
 
OptionFECPacketSett: 1 -> Turn on Forward Error Correction Switch (Default)
OptionTranPower    : 0 -> 22dBm (Default)
OptionIODrive: 1 -> TXD, RXD, AUX are push-pulls/pull-ups (default)
OptionFixedTransmission: 0 -> Transparent transmission (default)
OptionWirelessWakeUPTime: 1 -> 1000ms (default)
----------------------------------------