Ebyte LoRa E32 per Arduino, esp32 o esp8266: specifiche ed utilizzo base – Parte 1

/*
 * LoRa E32-TTL-100
 * Start device or reset to send a message
 * https://mischianti.org
 *
 * E32-TTL-100----- Arduino UNO
 * M0         ----- GND
 * M1         ----- GND
 * TX         ----- PIN 2 (PullUP)
 * RX         ----- PIN 3 (PullUP & Voltage divider)
 * AUX        ----- Not connected
 * VCC        ----- 3.3v/5v
 * GND        ----- GND
 *
 */
#include "Arduino.h"

#include <SoftwareSerial.h>

SoftwareSerial mySerial(2, 3);  // e32 TX e32 RX

void setup() {
  Serial.begin(9600);
  delay(500);

  Serial.println("Hi, I'm going to send message!");

  mySerial.begin(9600);
  mySerial.println("Hello, world?");
}

void loop() {
  if (mySerial.available()) {
    Serial.write(mySerial.read());
  }
  if (Serial.available()) {
    mySerial.write(Serial.read());
  }
}

/*
 * LoRa E32-TTL-100
 * Start device or reset to send a message
 * https://mischianti.org
 *
 * E32-TTL-100----- Wemos D1 mini
 * M0         ----- GND
 * M1         ----- GND
 * TX         ----- PIN D2 (PullUP)
 * RX         ----- PIN D3 (PullUP)
 * AUX        ----- Not connected
 * VCC        ----- 3.3v/5v
 * GND        ----- GND
 *
 */
#include "Arduino.h"
#include <SoftwareSerial.h>

SoftwareSerial mySerial(D2, D3); // e32 TX e32 RX

void setup() {
  Serial.begin(9600);
  delay(500);

  Serial.println("Hi, I'm going to send message!");

  mySerial.begin(9600);
  mySerial.println("Hello, world?");
}

void loop() {
  if (mySerial.available()) {
    Serial.write(mySerial.read());
  }
  if (Serial.available()) {
    mySerial.write(Serial.read());
  }
}

/*
 * LoRa E32
 * Start device or reset to send a message
 * https://mischianti.org
 *
 * E32        ----- esp32
 * M0         ----- GND
 * M1         ----- GND
 * TX         ----- RX2 (PullUP)
 * RX         ----- TX2 (PullUP)
 * AUX        ----- Not connected
 * VCC        ----- 3.3v/5v
 * GND        ----- GND
 *
 */
#include "Arduino.h"

void setup() {
  Serial.begin(9600);
  delay(500);

  Serial.println("Hi, I'm going to send message!");

  Serial2.begin(9600);
  Serial2.println("Hello, world?");
}

void loop() {
  if (Serial2.available()) {
    Serial.write(Serial2.read());
  }
  if (Serial.available()) {
    Serial2.write(Serial.read());
  }
}

/*
 * LoRa E32
 * Start device or reset to send a message
 * https://mischianti.org
 *
 * E32        ----- Arduino MKR WiFi 1010
 * M0         ----- 2 (or GND)
 * M1         ----- 3 (or GND)
 * RX         ----- 14 (PullUP)
 * TX         ----- 13 (PullUP)
 * AUX        ----- 1  (PullUP)
 * VCC        ----- 3.3v/5v
 * GND        ----- GND
 *
 */
#include "Arduino.h"

void setup() {
  Serial.begin(9600);
  delay(500);

  Serial.println("Hi, I'm going to send message!");

  Serial1.begin(9600);
  Serial1.println("Hello, world?");
}

void loop() {
  if (Serial1.available()) {
    Serial.write(Serial1.read());
  }
  if (Serial.available()) {
    Serial1.write(Serial.read());
  }
}

/*
 * LoRa E32-TTL-100
 * Write on serial to transfer a message to other device
 * https://mischianti.org
 *
 * E32-TTL-100----- Arduino UNO
 * M0         ----- GND
 * M1         ----- GND
 * TX         ----- PIN 2 (PullUP)
 * RX         ----- PIN 3 (PullUP & Voltage divider)
 * AUX        ----- Not connected
 * VCC        ----- 3.3v/5v
 * GND        ----- GND
 *
 */
#include "Arduino.h"
#include "LoRa_E32.h"

LoRa_E32 e32ttl100(2, 3); // e32 TX e32 RX

void setup() {
  Serial.begin(9600);
  delay(500);

  Serial.println("Hi, I'm going to send message!");

  // Startup all pins and UART
  e32ttl100.begin();

  // Send message
  ResponseStatus rs = e32ttl100.sendMessage("Hello, world?");
  // Check If there is some problem of successfully send
  Serial.println(rs.getResponseDescription());
}

void loop() {
	// If something available
  if (e32ttl100.available()>1) {
	  // read the String message
	ResponseContainer rc = e32ttl100.receiveMessage();
	// Is something goes wrong print error
	if (rc.status.code!=1){
		rc.status.getResponseDescription();
	}else{
		// Print the data received
		Serial.println(rc.data);
	}
  }
  if (Serial.available()) {
	  String input = Serial.readString();
	  e32ttl100.sendMessage(input);
  }
}

/*
 * LoRa E32-TTL-100
 * Start device or reset to send a message
 * https://mischianti.org
 *
 * E32-TTL-100----- Wemos D1 mini
 * M0         ----- GND
 * M1         ----- GND
 * TX         ----- PIN D2 (PullUP)
 * RX         ----- PIN D3 (PullUP)
 * AUX        ----- Not connected
 * VCC        ----- 3.3v/5v
 * GND        ----- GND
 *
 */
#include "Arduino.h"
#include "LoRa_E32.h"

LoRa_E32 e32ttl100(D2, D3); // e32 TX e32 RX

void setup() {
  Serial.begin(9600);
  delay(500);

  Serial.println("Hi, I'm going to send message!");

  // Startup all pins and UART
  e32ttl100.begin();

  // Send message
  ResponseStatus rs = e32ttl100.sendMessage("Hello, world?");
  // Check If there is some problem of successfully send
  Serial.println(rs.getResponseDescription());
}

void loop() {
	// If something available
  if (e32ttl100.available()>1) {
	  // read the String message
	ResponseContainer rc = e32ttl100.receiveMessage();
	// Is something goes wrong print error
	if (rc.status.code!=1){
		rc.status.getResponseDescription();
	}else{
		// Print the data received
		Serial.println(rc.data);
	}
  }
  if (Serial.available()) {
	  String input = Serial.readString();
	  e32ttl100.sendMessage(input);
  }
}

/*
 * EBYTE LoRa E32
 * send a transparent message, you must check that the transmitter and receiver have the same
 * CHANNEL ADDL and ADDH
 *
 *
 * https://mischianti.org
 *
 * E32		  ----- esp32
 * M0         ----- 19 (or GND)
 * M1         ----- 21 (or GND)
 * RX         ----- TX2 (PullUP)
 * TX         ----- RX2 (PullUP)
 * AUX        ----- 15  (PullUP)
 * VCC        ----- 3.3v/5v
 * GND        ----- GND
 *
 */

#include "Arduino.h"
#include "LoRa_E32.h"

// ---------- esp8266 pins --------------
//LoRa_E32 e32ttl(RX, TX, AUX, M0, M1);  // Arduino RX <-- e22 TX, Arduino TX --> e22 RX
//LoRa_E32 e32ttl(D3, D4, D5, D7, D6); // Arduino RX <-- e22 TX, Arduino TX --> e22 RX AUX M0 M1
//LoRa_E32 e32ttl(D2, D3); // Config without connect AUX and M0 M1

//#include <SoftwareSerial.h>
//SoftwareSerial mySerial(D2, D3); // Arduino RX <-- e22 TX, Arduino TX --> e22 RX
//LoRa_E32 e32ttl(&mySerial, D5, D7, D6); // AUX M0 M1
// -------------------------------------

// ---------- Arduino pins --------------
//LoRa_E32 e32ttl(4, 5, 3, 7, 6); // Arduino RX <-- e22 TX, Arduino TX --> e22 RX AUX M0 M1
//LoRa_E32 e32ttl(4, 5); // Config without connect AUX and M0 M1

//#include <SoftwareSerial.h>
//SoftwareSerial mySerial(4, 5); // Arduino RX <-- e22 TX, Arduino TX --> e22 RX
//LoRa_E32 e32ttl(&mySerial, 3, 7, 6); // AUX M0 M1
// -------------------------------------

// ------------- Arduino MKR WiFi 1010 -------------
// LoRa_E32 e220ttl(&Serial1, 1, 2, 3); //  RX AUX M0 M1
// -------------------------------------------------

// ---------- esp32 pins --------------
LoRa_E32 e32ttl(&Serial2, 15, 21, 19); //  RX AUX M0 M1

//LoRa_E32 e32ttl(&Serial2, 22, 4, 18, 21, 19, UART_BPS_RATE_9600); //  esp32 RX <-- e22 TX, esp32 TX --> e22 RX AUX M0 M1
// -------------------------------------

void setup() {
  Serial.begin(9600);
  delay(500);

  // Startup all pins and UART
  e32ttl.begin();

  Serial.println("Hi, I'm going to send message!");

  // Send message
  ResponseStatus rs = e32ttl.sendMessage("Hello, world?");
  // Check If there is some problem of succesfully send
  Serial.println(rs.getResponseDescription());
}

void loop() {
	// If something available
  if (e32ttl.available()>1) {
	  // read the String message
	ResponseContainer rc = e32ttl.receiveMessage();

	// Is something goes wrong print error
	if (rc.status.code!=1){
		Serial.println(rc.status.getResponseDescription());
	}else{
		// Print the data received
		Serial.println(rc.status.getResponseDescription());
		Serial.println(rc.data);
	}
  }
  if (Serial.available()) {
	  String input = Serial.readString();
	  e32ttl.sendMessage(input);
  }
}

/*
 * EBYTE LoRa E32
 * send a transparent message, you must check that the transmitter and receiver have the same
 * CHANNEL ADDL and ADDH
 *
 *
 * https://mischianti.org
 *
 * E32		  ----- Arduino MKR
 * M0         ----- 2 (or GND)
 * M1         ----- 3 (or GND)
 * RX         ----- 14 (PullUP)
 * TX         ----- 13 (PullUP)
 * AUX        ----- 1  (PullUP)
 * VCC        ----- 3.3v/5v
 * GND        ----- GND
 *
 */

#include "Arduino.h"
#include "LoRa_E32.h"

// ---------- esp8266 pins --------------
//LoRa_E32 e32ttl(RX, TX, AUX, M0, M1);  // Arduino RX <-- e22 TX, Arduino TX --> e22 RX
//LoRa_E32 e32ttl(D3, D4, D5, D7, D6); // Arduino RX <-- e22 TX, Arduino TX --> e22 RX AUX M0 M1
//LoRa_E32 e32ttl(D2, D3); // Config without connect AUX and M0 M1

//#include <SoftwareSerial.h>
//SoftwareSerial mySerial(D2, D3); // Arduino RX <-- e22 TX, Arduino TX --> e22 RX
//LoRa_E32 e32ttl(&mySerial, D5, D7, D6); // AUX M0 M1
// -------------------------------------

// ---------- Arduino pins --------------
//LoRa_E32 e32ttl(4, 5, 3, 7, 6); // Arduino RX <-- e22 TX, Arduino TX --> e22 RX AUX M0 M1
//LoRa_E32 e32ttl(4, 5); // Config without connect AUX and M0 M1

//#include <SoftwareSerial.h>
//SoftwareSerial mySerial(4, 5); // Arduino RX <-- e22 TX, Arduino TX --> e22 RX
//LoRa_E32 e32ttl(&mySerial, 3, 7, 6); // AUX M0 M1
// -------------------------------------

// ------------- Arduino MKR WiFi 1010 -------------
LoRa_E32 e220ttl(&Serial1, 1, 2, 3); //  RX AUX M0 M1
// -------------------------------------------------

// ---------- esp32 pins --------------
// LoRa_E32 e32ttl(&Serial2, 15, 21, 19); //  RX AUX M0 M1

//LoRa_E32 e32ttl(&Serial2, 22, 4, 18, 21, 19, UART_BPS_RATE_9600); //  esp32 RX <-- e22 TX, esp32 TX --> e22 RX AUX M0 M1
// -------------------------------------

void setup() {
  Serial.begin(9600);
  delay(500);

  // Startup all pins and UART
  e32ttl.begin();

  Serial.println("Hi, I'm going to send message!");

  // Send message
  ResponseStatus rs = e32ttl.sendMessage("Hello, world?");
  // Check If there is some problem of succesfully send
  Serial.println(rs.getResponseDescription());
}

void loop() {
	// If something available
  if (e32ttl.available()>1) {
	  // read the String message
	ResponseContainer rc = e32ttl.receiveMessage();

	// Is something goes wrong print error
	if (rc.status.code!=1){
		Serial.println(rc.status.getResponseDescription());
	}else{
		// Print the data received
		Serial.println(rc.status.getResponseDescription());
		Serial.println(rc.data);
	}
  }
  if (Serial.available()) {
	  String input = Serial.readString();
	  e32ttl.sendMessage(input);
  }
}

//  If you have ever change configuration you must restore It
	ResponseStructContainer c;
	c = e32ttl100.getConfiguration();
	Configuration configuration = *(Configuration*) c.data;
	Serial.println(c.status.getResponseDescription());
	configuration.CHAN = 0x17;
	configuration.OPTION.fixedTransmission = FT_TRANSPARENT_TRANSMISSION;
	e32ttl100.setConfiguration(configuration, WRITE_CFG_PWR_DWN_SAVE);