Renzo Mischianti

Forum Replies Created

Viewing 2 posts - 1 through 2 (of 2 total)

Author

Posts

26 July 2024 at 07:00 in reply to: ESP32 with Lora E32 not receiving data #31087

Participant

Hi Julio,
I am using tx2,rx2 pins . But i am using esp32-c6 board. So pins would be different.
E32 PIN ESP32 PINS
AUX 1
M0 10
M1 11

Drop me an email on adi1316@gmail.com for any issue.

17 June 2024 at 10:54 in reply to: ESP32 with Lora E32 not receiving data #30822

adi1316

Participant

Thanks Renzo for your support.

//Sender Config

//Sender Config
13:42:53.345 -> RX MIC ---> -1
13:42:53.345 -> TX MIC ---> -1
13:42:53.345 -> TX Const ---> 6
13:42:53.345 -> AUX ---> 23
13:42:53.418 -> M0 ---> 10
13:42:53.418 -> M1 ---> 11
13:42:53.418 -> Init AUX pin!
13:42:53.418 -> Init M0 pin!
13:42:53.418 -> Init M1 pin!
13:42:53.498 -> Begin ex
13:42:53.498 -> Begin Hardware Serial
13:42:53.498 -> Begin 
13:42:53.498 -> MODE NORMAL!
13:42:53.535 -> AUX HIGH!
13:42:53.535 -> Complete!
13:42:53.568 -> MODE PROGRAM/SLEEP!
13:42:53.608 -> AUX HIGH!
13:42:53.608 -> Complete!
13:42:53.728 -> Available buffer: 6 structure size: 6
13:42:53.728 -> AUX HIGH!
13:42:53.728 -> Complete!
13:42:53.728 -> ----------------------------------------
13:42:53.797 -> HEAD : 11000000 192 C0
13:42:53.797 ->  
13:42:53.880 -> AddH : 0
13:42:53.880 -> AddL : 1
13:42:53.880 -> Chan : 4 -> 414MHz
13:42:53.880 ->  
13:42:53.880 -> SpeedParityBit     : 0 -> 8N1 (Default)
13:42:53.915 -> SpeedUARTDatte  : 11 -> 9600bps (default)
13:42:53.998 -> SpeedAirDataRate   : 10 -> 2.4kbps (default)
13:42:53.998 -> OptionTrans        : 1 -> Fixed transmission (first three bytes can be used as high/low address and channel)
13:42:54.113 -> OptionPullup       : 1 -> TXD, RXD, AUX are push-pulls/pull-ups
13:42:54.182 -> OptionWakeup       : 100 -> 1250ms
13:42:54.263 -> OptionFEC          : 1 -> Turn on Forward Error Correction Switch (Default)
13:42:54.332 -> OptionPower        : 11 -> 10dBm
13:42:54.332 -> ----------------------------------------
13:42:54.398 -> ----------------------------------------
13:42:54.479 -> HEAD BIN INSIDE: 11000000 192 C0
13:42:54.479 -> ----------------------------------------
13:42:54.479 -> MODE NORMAL!
13:42:54.514 -> AUX HIGH!
13:42:54.514 -> Complete!
13:42:54.514 -> Complete!
13:42:54.579 -> MODE PROGRAM/SLEEP!
13:42:54.612 -> AUX HIGH!
13:42:54.653 -> Complete!
13:42:54.696 -> AUX HIGH!
13:42:54.764 -> Complete!
13:42:54.764 -> Clear buffer...ok!

//Receiver Config

13:29:58.427 -> RX MIC ---> -1
13:29:58.427 -> TX MIC ---> -1
13:29:58.427 -> TX Const ---> 6
13:29:58.427 -> AUX ---> 1
13:29:58.427 -> M0 ---> 10
13:29:58.495 -> M1 ---> 11
13:29:58.495 -> Init AUX pin!
13:29:58.495 -> Init M0 pin!
13:29:58.495 -> Init M1 pin!
13:29:58.574 -> Begin ex
13:29:58.574 -> Begin Hardware Serial
13:29:58.574 -> Begin 
13:29:58.574 -> MODE NORMAL!
13:29:58.574 -> AUX HIGH!
13:29:58.610 -> Complete!
13:29:58.646 -> MODE PROGRAM/SLEEP!
13:29:58.685 -> AUX HIGH!
13:29:58.685 -> Complete!
13:29:58.819 -> Available buffer: 6 structure size: 6
13:29:58.819 -> AUX HIGH!
13:29:58.819 -> Complete!
13:29:58.819 -> ----------------------------------------
13:29:58.861 -> HEAD : 11000000 192 C0
13:29:58.861 ->  
13:29:58.956 -> AddH : 0
13:29:58.956 -> AddL : 3
13:29:58.956 -> Chan : 4 -> 414MHz
13:29:58.956 ->  
13:29:58.956 -> SpeedParityBit     : 0 -> 8N1 (Default)
13:29:58.989 -> SpeedUARTDatte  : 11 -> 9600bps (default)
13:29:59.059 -> SpeedAirDataRate   : 10 -> 2.4kbps (default)
13:29:59.059 -> OptionTrans        : 1 -> Fixed transmission (first three bytes can be used as high/low address and channel)
13:29:59.179 -> OptionPullup       : 1 -> TXD, RXD, AUX are push-pulls/pull-ups
13:29:59.258 -> OptionWakeup       : 100 -> 1250ms
13:29:59.324 -> OptionFEC          : 1 -> Turn on Forward Error Correction Switch (Default)
13:29:59.391 -> OptionPower        : 11 -> 10dBm
13:29:59.474 -> ----------------------------------------
13:29:59.540 -> HEAD BIN INSIDE: 11000000 192 C0
13:29:59.540 -> ----------------------------------------
13:29:59.575 -> MODE NORMAL!
13:29:59.575 -> AUX HIGH!
13:29:59.626 -> Complete!
13:29:59.626 -> Updtaed config is 
13:29:59.662 -> MODE PROGRAM/SLEEP!
13:29:59.662 -> AUX HIGH!
13:29:59.705 -> Complete!
13:29:59.739 -> AUX HIGH!
13:29:59.805 -> Complete!
13:29:59.805 -> Clear buffer...ok!
13:29:59.805 -> ----------------------------------------
13:29:59.872 -> HEAD BIN INSIDE: 11000000 192 C0
13:29:59.872 -> ----------------------------------------
13:29:59.941 -> MODE NORMAL!
13:29:59.972 -> AUX HIGH!
13:30:00.006 -> Complete!
13:30:00.006 -> Config: Success

I have powering the sender/transmitter node with power bank and its working fine now.

Can you please check the configuration once and confirm if it is production deploy ready?

Also below is the updated code for your reference, if it needs any change

Updated Sender Code


//Sender
#include "Arduino.h"
#define E32_TTL_1W
#include "LoRa_E32.h"
#define FREQUENCY_868
#define AUX 23
#define M0 10
#define M1 11
#define txpin 5
#define rxpin 4
//HardwareSerial serial1(2);

//LoRa_E32 e32ttl1w(txpin, rxpin, &Serial1, AUX, M0, M1, UART_BPS_RATE_9600);
LoRa_E32 e32ttl1w(&Serial1, AUX, M0, M1);
void printParameters(struct Configuration configuration);
void printModuleInformation(struct ModuleInformation moduleInformation);

// Variables globales
unsigned long interval = 15000;          // interval between sends
unsigned long lastSendTime = 0;        // last send time
byte msgCount = 0;            // count of outgoing messages
long randNumber;
void setup() {
  //Inicio comunicacion serie con monitor
  Serial.begin(9600);
  delay(500);

  Serial.println("In setup");

  e32ttl1w.begin();

  //Configuro el nodo LoRa
  nodeConfig();
}

void loop() {
  // Wait a few seconds between measurements.

  if (millis() - lastSendTime > interval) {
    // print a random number from 10 to 19
    randNumber = random(10, 20);
    String trama = String(randNumber);
    ResponseStatus rs = e32ttl1w.sendFixedMessage(0x0, 0x3, 0x4, trama);
    Serial.println("Sending " + trama);
    Serial.println(rs.getResponseDescription());
    lastSendTime = millis();            // timestamp the message
    msgCount++;
  }
  delay(100);
}

void nodeConfig(){

  ResponseStructContainer c;
  c = e32ttl1w.getConfiguration();
  Configuration configuration = *(Configuration*) c.data;

  configuration.ADDH        = 0x0;
  configuration.ADDL        = 0x1;
  configuration.CHAN        = 0x4;

  configuration.SPED.airDataRate           = AIR_DATA_RATE_010_24;
  configuration.SPED.uartBaudRate          = UART_BPS_9600;
  configuration.SPED.uartParity            = MODE_00_8N1;
  configuration.OPTION.fec                 = FEC_1_ON;
  configuration.OPTION.fixedTransmission   = FT_FIXED_TRANSMISSION;
  configuration.OPTION.ioDriveMode         = IO_D_MODE_PUSH_PULLS_PULL_UPS;
  configuration.OPTION.transmissionPower   = POWER_21;
  configuration.OPTION.wirelessWakeupTime  = WAKE_UP_1250;
  //printParameters(configuration);
  c.close();
// Set configuration changed and set to not hold the configuration
  ResponseStatus rs = e32ttl1w.setConfiguration(configuration, WRITE_CFG_PWR_DWN_SAVE);
  Serial.print("Config: ");
  Serial.println(rs.getResponseDescription());
}

Updated Receiver Code


//Receiver Code
#include "Arduino.h"
#define E32_TTL_1W
#include "LoRa_E32.h"
#define AUX 1
#define M0 10
#define M1 11

LoRa_E32 e32ttl1w(&Serial1, AUX, M0, M1);
ResponseContainer rc;
void setup() {
//Inicio comunicacion serie con monitor
	Serial.begin(9600);
  Serial.println("In setup mode");
	delay(500);
// Startup all pins and UART
	e32ttl1w.begin();
//Configuro el nodo LoRa
	nodeConfig();
  //delay(4000);
  //fetchConfig();
}

void loop() {
	if (e32ttl1w.available() > 0) {
		Serial.println("———-");
		rc = e32ttl1w.receiveMessageUntil();
    //rc.close();
// If something goes wrong print error
		if (rc.status.code != 1) {
			rc.status.getResponseDescription();
      
		} else {
// Print the data received
			Serial.println(rc.data);
		}
    //rc.close();
	}
	delay(100);
}

void nodeConfig() {
	ResponseStructContainer c;
	c = e32ttl1w.getConfiguration();
	Configuration configuration = *(Configuration*) c.data;
	configuration.ADDH = 0x0;
	configuration.ADDL = 0x3;
	configuration.CHAN = 0x4;
	configuration.SPED.airDataRate = AIR_DATA_RATE_010_24;
	configuration.SPED.uartBaudRate = UART_BPS_9600;
	configuration.SPED.uartParity = MODE_00_8N1;
	configuration.OPTION.fec = FEC_1_ON;
	configuration.OPTION.fixedTransmission = FT_FIXED_TRANSMISSION;
	configuration.OPTION.ioDriveMode = IO_D_MODE_PUSH_PULLS_PULL_UPS;
	configuration.OPTION.transmissionPower = POWER_21;
	configuration.OPTION.wirelessWakeupTime = WAKE_UP_1250;
// Set configuration changed and set to not hold the configuration
  c.close();
  Serial.println("Updtaed config is ");
  
	ResponseStatus rs = e32ttl1w.setConfiguration(configuration, WRITE_CFG_PWR_DWN_SAVE);
	Serial.print("Config: ");
	Serial.println(rs.getResponseDescription());
}

Author

Posts

Viewing 2 posts - 1 through 2 (of 2 total)