[Renzo Mischianti]

Hi Fabiooo,
the problem of deep sleep was explained here, to be sure to read the message you must use light sleep.
The power-consuming difference isn’t so big, so It’s preferable.
Bye Renzo

[Renzo Mischianti]

Hi Fabiooo,
if you have a (minimal) memory leak, probably write over the memory location of the received message variable or at the sending time.
Bye Renzo

[Renzo Mischianti]

hi Fabioo,
It’s very strange; It’s possible that there are some issues with the power supply.
Or a bad usage of memory allocation?
Bye Renzo

[Renzo Mischianti]

Thanks a lot. Your work is precious.
Bye Renzo

[Renzo Mischianti]

Sorry Woto,
if you set the ADDH, ADDL, and CHAN with the same value, you have configured the devices to communicate in transparent transmission.

To use fixed transmission, you must set a different ADDH or ADDL and send the message from the first by setting the receiver’s destination address.

So, if you have configured the sender

ADDH = 00
ADDL = 03
CHAN = 18

you must configure the receiver

ADDH = 00
ADDL = 04
CHAN = 18

and in the sender
ResponseStatus rs = e220ttl.sendFixedMessage(0, 4, 18, "Hello, world?");

But I think you must check the articles, they can be more clean.

Bye Renzo

[Renzo Mischianti]

Hi woto,
you have configured the Address and Channel for transparent transmission and set fixed transmission.

Follow these tutorials to send fixed message
Ebyte LoRa E220 device for Arduino, esp32 or esp8266: fixed transmission, broadcast, monitor, and RSSI – 4

this is for E32 and micropython but you can get some ideas
EByte LoRa E32 & MicroPython: a deep dive into transmission types – 4

Bye Renzo

• This reply was modified 12 months ago by Renzo Mischianti.

[Renzo Mischianti]

Hi woto,
you don’t need to change the library.
You can find how to use the library for e32 (similar to E220) in this article.
EByte LoRa E32 & MicroPython: a detailed look at configuration – 3
I create a specified tutorial for E220 soon.

code, configuration = lora.get_configuration()
configuration.CHAN = 18
code, configuration = lora.set_configuration(configuration)

Bye Renzo

• This reply was modified 12 months ago by Renzo Mischianti.
• This reply was modified 12 months ago by Renzo Mischianti.

[Renzo Mischianti]

Hi MAWMN,
not inside the library, but I think you can check the millis(), and if you already have a click in a specified interval, you can abort the previous action and activate the new one.
But pay attention, if you already clicked one and after that interval, no other action was activated, you must execute the click function.
Bye Renzo

[Renzo Mischianti]

If you need something more specified ask here.
Bye Renzo

[Renzo Mischianti]

Hi Carcela,
to create a network, you can follow the instructions in this article

Ebyte LoRa E22 device for Arduino, esp32 or esp8266: fixed transmission, broadcast, monitor, and RSSI – 4

you can also use the repeater function to manage devices with a lot of distance

EByte LoRa E22 repeater mode schema

Bye Renzo

[Renzo Mischianti]

Hi Orhan,
you must connect the AUX pin and try to manage the air data rate and baud rate, but the frequency can be variable because of FEC and waiting for the transmission, so disable It.
Bye Renzo

[Renzo Mischianti]

Hi Srill,
haaa perfect!
No, I think it’s not possible, they use a different chip to implement the communication.
Bye Renzo

[Renzo Mischianti]

Hi Srill,
you must pass the reference of Serial.

LoRa_E32 e32ttl(&Serial2, 15, 33, 32);

Bye Renzo

[Renzo Mischianti]

Hi,
check if another process uses the port.

netstat -an

Bye Renzo

[Renzo Mischianti]

Hi,
remove all unneeded lines like

SoftwareSerial mySerial(D2, D3);

pin declaration etc. and retry.
Bye Renzo

[Author]

Posts