Transmission Does NOT Work

This topic has 14 replies, 2 voices, and was last updated 3 years, 10 months ago by Renzo Mischianti.

Viewing 4 reply threads

Author

Posts

7 June 2021 at 15:08 #12435

Participant

The following is for the TX.


#include "Arduino.h"
#include "LoRa_E32.h"

#include "SoftwareSerial.h"

LoRa_E32 e32ttl(2, 3, 5, 6, 9);

void printParameters(struct Configuration configuration);
void printModuleInformation(struct ModuleInformation moduleInformation);
//The setup function is called once at startup of the sketch
void setup() {
	Serial.begin(9600);
	while (!Serial) {
		; // wait for serial port to connect. Needed for native USB
	}
	delay(100);

	e32ttl.begin();

// After set configuration comment set M0 and M1 to low
// and reboot if you directly set HIGH M0 and M1 to program
	ResponseStructContainer c;
	c = e32ttl.getConfiguration();
	Configuration configuration = *(Configuration*) c.data;
	configuration.ADDL = 1;
	configuration.ADDH = 0;
	configuration.CHAN = 23;
	configuration.OPTION.fixedTransmission = FT_FIXED_TRANSMISSION;

	configuration.OPTION.transmissionPower = POWER_20; // dBm transmission power
	configuration.OPTION.wirelessWakeupTime = WAKE_UP_250; // Wait time for wake up

	configuration.SPED.airDataRate = AIR_DATA_RATE_000_03; // Air data rate
	configuration.SPED.uartBaudRate = UART_BPS_9600;

	printParameters(configuration);
// ---------------------------
}

// The loop function is called in an endless loop
void loop() {
	delay(2000);

	Serial.println("Send message to 00 03 04");
	ResponseStatus rs = e32ttl.sendFixedMessage(0, 3, 23, "yuiuyiuyiu");
	Serial.println(rs.getResponseDescription());
}

void printParameters(struct Configuration configuration) {
	Serial.println("----------------------------------------");

	Serial.print(F("HEAD : "));
	Serial.print(configuration.HEAD, BIN);
	Serial.print(" ");
	Serial.print(configuration.HEAD, DEC);
	Serial.print(" ");
	Serial.println(configuration.HEAD, HEX);
	Serial.println(F(" "));
	Serial.print(F("AddH : "));
	Serial.println(configuration.ADDH, BIN);
	Serial.print(F("AddL : "));
	Serial.println(configuration.ADDL, BIN);
	Serial.print(F("Chan : "));
	Serial.print(configuration.CHAN, DEC);
	Serial.print(" -> ");
	Serial.println(configuration.getChannelDescription());
	Serial.println(F(" "));
	Serial.print(F("SpeedParityBit : "));
	Serial.print(configuration.SPED.uartParity, BIN);
	Serial.print(" -> ");
	Serial.println(configuration.SPED.getUARTParityDescription());
	Serial.print(F("SpeedUARTDatte : "));
	Serial.print(configuration.SPED.uartBaudRate, BIN);
	Serial.print(" -> ");
	Serial.println(configuration.SPED.getUARTBaudRate());
	Serial.print(F("SpeedAirDataRate : "));
	Serial.print(configuration.SPED.airDataRate, BIN);
	Serial.print(" -> ");
	Serial.println(configuration.SPED.getAirDataRate());

	Serial.print(F("OptionTrans : "));
	Serial.print(configuration.OPTION.fixedTransmission, BIN);
	Serial.print(" -> ");
	Serial.println(configuration.OPTION.getFixedTransmissionDescription());
	Serial.print(F("OptionPullup : "));
	Serial.print(configuration.OPTION.ioDriveMode, BIN);
	Serial.print(" -> ");
	Serial.println(configuration.OPTION.getIODroveModeDescription());
	Serial.print(F("OptionWakeup : "));
	Serial.print(configuration.OPTION.wirelessWakeupTime, BIN);
	Serial.print(" -> ");
	Serial.println(configuration.OPTION.getWirelessWakeUPTimeDescription());
	Serial.print(F("OptionFEC : "));
	Serial.print(configuration.OPTION.fec, BIN);
	Serial.print(" -> ");
	Serial.println(configuration.OPTION.getFECDescription());
	Serial.print(F("OptionPower : "));
	Serial.print(configuration.OPTION.transmissionPower, BIN);
	Serial.print(" -> ");
	Serial.println(configuration.OPTION.getTransmissionPowerDescription());

	Serial.println("----------------------------------------");

}
void printModuleInformation(struct ModuleInformation moduleInformation) {
	Serial.println("----------------------------------------");
	Serial.print(F("HEAD BIN: "));
	Serial.print(moduleInformation.HEAD, BIN);
	Serial.print(" ");
	Serial.print(moduleInformation.HEAD, DEC);
	Serial.print(" ");
	Serial.println(moduleInformation.HEAD, HEX);

	Serial.print(F("Freq.: "));
	Serial.println(moduleInformation.frequency, HEX);
	Serial.print(F("Version : "));
	Serial.println(moduleInformation.version, HEX);
	Serial.print(F("Features : "));
	Serial.println(moduleInformation.features, HEX);
	Serial.println("----------------------------------------");

}

Serial monitor

///


#include "Arduino.h"
#include "LoRa_E32.h"
#include "SoftwareSerial.h"

LoRa_E32 e32ttl(2, 3, 5, 6, 7);

void printParameters(struct Configuration configuration);
void printModuleInformation(struct ModuleInformation moduleInformation);
//The setup function is called once at startup of the sketch
void setup() {
	Serial.begin(9600);
	while (!Serial) {
		; // wait for serial port to connect. Needed for native USB
	}
	delay(100);

	e32ttl.begin();

// e32ttl.resetModule();
// After set configuration comment set M0 and M1 to low
// and reboot if you directly set HIGH M0 and M1 to program
	ResponseStructContainer c;
	c = e32ttl.getConfiguration();
	Configuration configuration = *(Configuration*) c.data;
	configuration.ADDL = 3;
	configuration.ADDH = 0;
	configuration.CHAN = 23;
	configuration.OPTION.fixedTransmission = FT_FIXED_TRANSMISSION;
	e32ttl.setConfiguration(configuration, WRITE_CFG_PWR_DWN_SAVE);
	printParameters(configuration);
// ---------------------------
	Serial.println();
	Serial.println("Start listening!");
}

// The loop function is called in an endless loop
void loop() {
	if (e32ttl.available() > 1) {
		ResponseContainer rs = e32ttl.receiveMessage();
// First of all get the data
		String message = rs.data;

		Serial.println(rs.status.getResponseDescription());
		Serial.println(message);
	}
	delay(100);
}

void printParameters(struct Configuration configuration) {
	Serial.println("----------------------------------------");

	Serial.print(F("HEAD : "));
	Serial.print(configuration.HEAD, BIN);
	Serial.print(" ");
	Serial.print(configuration.HEAD, DEC);
	Serial.print(" ");
	Serial.println(configuration.HEAD, HEX);
	Serial.println(F(" "));
	Serial.print(F("AddH : "));
	Serial.println(configuration.ADDH, DEC);
	Serial.print(F("AddL : "));
	Serial.println(configuration.ADDL, DEC);
	Serial.print(F("Chan : "));
	Serial.print(configuration.CHAN, DEC);
	Serial.print(" -> ");
	Serial.println(configuration.getChannelDescription());
	Serial.println(F(" "));
	Serial.print(F("SpeedParityBit : "));
	Serial.print(configuration.SPED.uartParity, BIN);
	Serial.print(" -> ");
	Serial.println(configuration.SPED.getUARTParityDescription());
	Serial.print(F("SpeedUARTDatte : "));
	Serial.print(configuration.SPED.uartBaudRate, BIN);
	Serial.print(" -> ");
	Serial.println(configuration.SPED.getUARTBaudRate());
	Serial.print(F("SpeedAirDataRate : "));
	Serial.print(configuration.SPED.airDataRate, BIN);
	Serial.print(" -> ");
	Serial.println(configuration.SPED.getAirDataRate());

	Serial.print(F("OptionTrans : "));
	Serial.print(configuration.OPTION.fixedTransmission, BIN);
	Serial.print(" -> ");
	Serial.println(configuration.OPTION.getFixedTransmissionDescription());
	Serial.print(F("OptionPullup : "));
	Serial.print(configuration.OPTION.ioDriveMode, BIN);
	Serial.print(" -> ");
	Serial.println(configuration.OPTION.getIODroveModeDescription());
	Serial.print(F("OptionWakeup : "));
	Serial.print(configuration.OPTION.wirelessWakeupTime, BIN);
	Serial.print(" -> ");
	Serial.println(configuration.OPTION.getWirelessWakeUPTimeDescription());
	Serial.print(F("OptionFEC : "));
	Serial.print(configuration.OPTION.fec, BIN);
	Serial.print(" -> ");
	Serial.println(configuration.OPTION.getFECDescription());
	Serial.print(F("OptionPower : "));
	Serial.print(configuration.OPTION.transmissionPower, BIN);
	Serial.print(" -> ");
	Serial.println(configuration.OPTION.getTransmissionPowerDescription());

	Serial.println("----------------------------------------");

}
void printModuleInformation(struct ModuleInformation moduleInformation) {
	Serial.println("----------------------------------------");
	Serial.print(F("HEAD BIN: "));
	Serial.print(moduleInformation.HEAD, BIN);
	Serial.print(" ");
	Serial.print(moduleInformation.HEAD, DEC);
	Serial.print(" ");
	Serial.println(moduleInformation.HEAD, HEX);

	Serial.print(F("Freq.: "));
	Serial.println(moduleInformation.frequency, HEX);
	Serial.print(F("Version : "));
	Serial.println(moduleInformation.version, HEX);
	Serial.print(F("Features : "));
	Serial.println(moduleInformation.features, HEX);
	Serial.println("----------------------------------------");
}

Serial monitor

All things seem to be alright, but it just cannot work.

Thanks for your reply.

7 June 2021 at 15:16 #12501
Renzo Mischianti
Keymaster
Hi C,
sorry if i answer only now, but with C name your post go on SPAM and I lost It.

Your speed air rate was different from sender and receiver. I think you must fix It.

Bye Renzo
8 June 2021 at 09:58 #12521
C
Participant
Thanks for your reply.

Sorry, I have fixed the air rate. The version I uploaded was not the latest.

All of the parameters are the same now.
- 8 June 2021 at 10:52 #12522
  Renzo Mischianti
  Keymaster
  Is everything working now? If you want share your project with us.
  Bye Renzo
- 8 June 2021 at 16:28 #12523
  C
  Participant
  not really
  
  All of the messages seem to be fine, but the transmission does not work.
  I think the problem here may be caused by the hardware, but the message said, “Success.”
  
  It’s really confusing.
- 10 June 2021 at 08:50 #12528
  Renzo Mischianti
  Keymaster
  Hi C,
  The success alert you that the sender device send the message, but it don’t kbow if a receiver receive it.
  
  Try with trasparent or check M0 M1.
  
  Enable debug and retry.
  Bye Renzo
6 July 2021 at 21:47 #13266
Jorge
Hi

I’m having the same problem. I’m using two Arduinos with two 868T20Ds, and using wiring and code from the fixed transmission tutorial. Both sender and receiver have the “Success” message and I have both with the exact same parameters, but the message from the sender is never received.

The only thing I have changed is the #define for my frequency, and everything seems to be alright, but somewhere something doesn’t work

Thanks in advance
- 6 July 2021 at 22:19 #13267
  Renzo Mischianti
  Keymaster
  Hi jorge,
  first try to get config to check if it’s all ok.
  If all ok retry in trasparent transmission.
  Then set configuration with save.
  And now resend the message.
  If not work try to change pull_up resistot.
  Bye Renzo
7 July 2021 at 23:18 #13278
Jorge
Hi, thanks for your reply

I have uploaded the getConfiguration code and I got the message “No response from device! (Check wiring)”, but I’ve checked the wiring and also changed the pull_up resistor and the message it’s still there.

In my case I doesn’t have a 4.7K resistor so I’m using 2x2K + 2×330 + 4×10 resistors in series instead, but I don’t think there’s the problem; I’ve checked them all and they work fine, and that’s the only change I have made from the wiring in the tutorial
- 8 July 2021 at 00:44 #13279
  Renzo Mischianti
  Keymaster
  Hi,
  try to remove the resistor, some device have some different setting.
  If problem continue try to change the e32 and execute the same code per try to reset with the EByte usb board.
  Bye Renzo
- 10 July 2021 at 12:17 #13368
  Jorge
  I’ve fixed the “No response from the device” problem, although it was unplugging the M0 and M1 pins instead of the resistor.
  
  Now, in getConfiguration I have “Success”, as well as in setConfiguration, where I’ve successfully uploaded and saved the configuration in both sender and receiver, but after all of that, I return to my original problem: Everything have “Success” state, but the message from the sender is never received by the receiver
- 10 July 2021 at 20:35 #13369
  Jorge
  It have turned really confusing.
  
  I continued testing and now the configuration in setConfiguration is not saving although it’s set for save it. The getConfiguration now returns success as state, but head is different in configuration and moduleInformation. I have tried it with another pair of modules and got the same results.
  
  I think the problem is somewhere around this methods, but I don’t know where is it or nor what I’m doing wrong.
- 10 July 2021 at 22:37 #13370
  Renzo Mischianti
  Keymaster
  Hi,
  I think the better solution is to reset all device with the original software and adaptor.
  Sometime when this device not wor tha software is the solution.
  Bye Renzo
- 11 July 2021 at 14:27 #13375
  Jorge
  Hi,
  
  How can I reset the modules ? Probably this is the case when the solution is to reset them, but I don’t know how to do it
- 12 July 2021 at 08:30 #13377
  Renzo Mischianti
  Keymaster
  Hi,
  I use this device
  https://s.click.aliexpress.com/e/_A4tZaa
  with the specified program for e32
  https://www.ebyte.com/en/pdf-down.aspx?id=199
  Bye Renzo