ESP32-C3-DevKitC-02: high-resolution pinout and specs

High resolution image

ESP32-C3-DevKitC-02 is an entry-level development board based on ESP32-C3-WROOM-02, a general-purpose module with 4 MB SPI flash. This board integrates complete Wi-Fi and Bluetooth LE functions.

Here my selection of microcontrollers LuatOS esp32c3 Core - ESP32-C3-DevKitC-02 - ESP32-C3-MINI-1 - WeMos LOLIN C3 PICO - WeMos LOLIN C3 Mini v2.1 - WeMos LOLIN C3 Mini v1.0 - ESP32 S3 Purlple AI-S3

Key Component	Description
ESP32-C3-WROOM-02	ESP32-C3-WROOM-02 from Espressif is a powerful and general-purpose module that offers Wi-Fi and Bluetooth LE coexistence. It has a PCB antenna and a 4 MB SPI flash.
5 V to 3.3 V LDO	Power regulator that converts a 5 V supply into a 3.3 V output.
5 V Power On LED	Turns on when the USB power is connected to the board.
Pin Headers	All available GPIO pins (except for the SPI bus for flash) are broken out to the pin headers on the board.
Boot Button	Download button. Holding down Boot and then pressing Reset initiates Firmware Download mode for downloading firmware through the serial port.
Micro-USB Port	USB interface. Power supply for the board as well as the communication interface between a computer and the ESP32-C3 chip.
Reset Button	Press this button to restart the system.
USB-to-UART Bridge	Single USB-to-UART bridge chip provides transfer rates up to 3 Mbps.
RGB LED	Addressable RGB LED, driven by GPIO8.

PINs

UART (Universal Asynchronous Receiver-Transmitter) pins:

• U0RXD (GPIO20): This pin serves as the UART0 receive (RX) pin, which is used for receiving serial data.
• U0TXD (GPIO21): This pin serves as the UART0 transmit (TX) pin, which is used for transmitting serial data.

I2C (Inter-Integrated Circuit) pins: The ESP32-C3 does not have dedicated I2C pins. However, you can implement software-based I2C (bit-banging) using any available GPIO pins. For instance, you could use GPIO12 (SPIHD) and GPIO13 (SPIWP) for the I2C SCL (clock) and SDA (data) pins, respectively.

LEDs: It has an RBG led that can be controlled with GPIO8 as RGB led, and with GPIO30 as normal led.

Specs

CPU and Memory

• 32-bit RISC-V single-core processor, up to 160
  MHz
• CoreMark® score:
  • 1 core at 160 MHz: 407.22 CoreMark; 2.55
    CoreMark/MHz
• 384 KB ROM
• 400 KB SRAM (16 KB for cache)
• 8 KB SRAM in RTC
• Embedded flash (see details in Chapter 1
  ESP32-C3 Series Comparison)
• SPI, Dual SPI, Quad SPI, and QPI interfaces that
  allow connection to multiple external flash
• Access to flash accelerated by cache
• Supports flash in-Circuit Programming (ICP)

Ordering Code	Embedded Flash	Ambient Temperature (°C)	Package (mm)	GPIO No.
ESP32-C3	No	–40 ∼ 105	QFN32 (5*5)	22
ESP32-C3FN4	4 MB	–40 ∼ 85	QFN32 (5*5)	22
ESP32-C3FH4	4 MB	–40 ∼ 105	QFN32 (5*5)	22
ESP32-C3FH4AZ	4 MB	–40 ∼ 105	QFN32 (5*5)	16

Advanced Peripheral Interfaces

• 22 or 16 programmable GPIOs
• Digital interfaces:
  • 3 × SPI
  • 2 × UART
  • 1 × I2C
  • 1 × I2S
  • Remote control peripheral, with 2 transmit
    channels and 2 receive channels
  • LED PWM controller, with up to 6 channels
  • Full-speed USB Serial/JTAG controller
  • General DMA controller (GDMA), with 3
    transmit channels and 3 receive channels
  • 1 × TWAI® controller compatible with ISO
    11898-1 (CAN Specification 2.0)
• Analog interfaces:
  • 2 × 12-bit SAR ADCs, up to 6 channels
  • 1 × temperature sensor
• Timers:
  • 2 × 54-bit general-purpose timers
  • 3 × digital watchdog timers
  • 1 × analog watchdog timer
  • 1 × 52-bit system timer

Wi­Fi

• IEEE 802.11 b/g/n-compliant
• Supports 20 MHz, 40 MHz bandwidth in 2.4
  GHz band
• 1T1R mode with data rate up to 150 Mbps
• 4 × virtual Wi-Fi interfaces
• 802.11mc FTM

Bluetooth

• Bluetooth LE: Bluetooth 5, Bluetooth mesh
• High power mode (21 dBm)
• Speed: 125 Kbps, 500 Kbps, 1 Mbps, 2 Mbps
• Advertising extensions
• Multiple advertisement sets
• Channel selection algorithm
• Internal co-existence mechanism between Wi-Fi
  and Bluetooth to share the same antenna

Security

• Secure boot
• Flash encryption
• 4096-bit OTP, up to 1792 bits for use
• Cryptographic hardware acceleration:
  • AES-128/256 (FIPS PUB 197)
• Permission Control
• SHA Accelerator (FIPS PUB 180-4)
• RSA Accelerator
• Random Number Generator (RNG)
• HMAC
• Digital signature

Low Power Management

• Power Management Unit with four power modes

How to

1. ESP32: pinout, specs and Arduino IDE configuration
2. ESP32: integrated SPIFFS Filesystem
3. ESP32: manage multiple Serial and logging
4. ESP32 practical power saving
   1. ESP32 practical power saving: manage WiFi and CPU
   2. ESP32 practical power saving: modem and light sleep
   3. ESP32 practical power saving: deep sleep and hibernation
   4. ESP32 practical power saving: preserve data, timer and touch wake up
   5. ESP32 practical power saving: external and ULP wake up
   6. ESP32 practical power saving: UART and GPIO wake up
5. ESP32: integrated LittleFS FileSystem
6. ESP32: integrated FFat (Fat/exFAT) FileSystem
7. ESP32-wroom-32
   1. ESP32-wroom-32: flash, pinout, specs and IDE configuration
8. ESP32-CAM
   1. ESP32-CAM: pinout, specs and Arduino IDE configuration
   2. ESP32-CAM: upgrade CamerWebServer with flash features
9. ESP32: use ethernet w5500 with plain (HTTP) and SSL (HTTPS)
10. ESP32: use ethernet enc28j60 with plain (HTTP) and SSL (HTTPS)
11. How to use SD card with esp32
12. esp32 and esp8266: FAT filesystem on external SPI flash memory

13. Firmware and OTA update management
    1. Firmware management
       1. ESP32: flash compiled firmware (.bin)
       2. ESP32: flash compiled firmware and filesystem (.bin) with GUI tools
    2. OTA update with Arduino IDE
       1. ESP32 OTA update with Arduino IDE: filesystem, firmware, and password
    3. OTA update with Web Browser
       1. ESP32 OTA update with Web Browser: firmware, filesystem, and authentication
       2. ESP32 OTA update with Web Browser: upload in HTTPS (SSL/TLS) with self-signed certificate
       3. ESP32 OTA update with Web Browser: custom web interface
    4. Self OTA uptate from HTTP server
       1. ESP32 self OTA update firmware from the server
       2. ESP32 self OTA update firmware from the server with version check
       3. ESP32 self-OTA update in HTTPS (SSL/TLS) with trusted self-signed certificate
    5. Non-standard Firmware update
       1. ESP32 firmware and filesystem update from SD card
       2. ESP32 firmware and filesystem update with FTP client

14. Integrating LAN8720 with ESP32 for Ethernet Connectivity with plain (HTTP) and SSL (HTTPS)
15. Connecting the EByte E70 to ESP32 c3/s3 devices and a simple sketch example
16. ESP32-C3: pinout, specs and Arduino IDE configuration

Datasheet

ESP32c3 datasheet

ESP32-C3-DevKitC-02 Schematic

PCB size

Thanks

• Arduino
  • UNO R3
  • UNO R3 CH340 SMD clone
  • Nano
• esp8285
  • DT-06
• esp8266
  • WeMos D1 mini
  • esp12 E
  • esp07
  • NodeMCU v2.x
  • NodeMCU v3.x
  • ESP-01
  • ESP-01S
• ESP32
  • DOIT ESP32 DEV KIT v1
  • ESP32 DevKitC v4
  • ESP32 WeMos LOLIN32
  • ESP32 WeMos LOLIN32 Lite
  • ESP32 WeMos LOLIN D32
  • ESP32-wroom-32
  • NodeMCU-32S
  • ESP32-S
  • ESP32-CAM
• ESP32 s2
  • ESP32 S2 Saola 1MI
  • Ai-thinker ESP 12K
• ESP32c3
  • ESP32-C3-DevKitC-02
  • LuatOS CORE-ESP32 C3
  • ESP32C3-MINI-DK
  • WeAct Studio ESP32 C3 Core
  • WeMos LOLIN ESP32 C3 mini v1.0
  • WeMos LOLIN ESP32 C3 mini v2.1
  • WeMos LOLIN ESP32 C3 pico
• ESP32s3
  • VCC-GND Studio YD-ESP32-S3
  • ESP32-S3 DevKitC 1
  • WeAct ESP32 S3 A
  • WeMos LOLIN S3
  • WeMos LOLIN S3 Pro
• Arduino SAMD
  • Arduino MKR WiFi 1010
  • Arduino NANO 33 IoT
• STM32
  • STM32F103C8T6 Blue Pill
  • STM32F103C6T6 Blue Pill
  • STM32F401CCU6 Black Pill
  • STM32F411CEU6 Black Pill
• Raspberry Pi
  • Pico
  • Pico W
  • WeAct Studio rp2040
  • Waweshare rp2040-zero